{"id":739,"date":"2010-02-10T03:18:40","date_gmt":"2010-02-10T11:18:40","guid":{"rendered":"http:\/\/www.todayifoundout.com\/?p=739"},"modified":"2016-08-04T00:51:34","modified_gmt":"2016-08-04T07:51:34","slug":"the-12-best-ways-to-remove-stripped-screws","status":"publish","type":"post","link":"https:\/\/www.todayifoundout.com\/index.php\/2010\/02\/the-12-best-ways-to-remove-stripped-screws\/","title":{"rendered":"The 12 Best Ways to Remove Stripped Screws"},"content":{"rendered":"

\"\"<\/a>Today I found out<\/a> twelve ways to remove a stripped screw.\u00a0 We’ve all been there; trying to void a warranty or otherwise take something apart and you go to take that one last screw off and invariably it strips.\u00a0 Now what?\u00a0 You can either A: Think Hammer… really, really big hammer; or B: Read the list below and pick the method that seems easiest to you on how to remove a stripped screw or bolt.<\/p>\n

    \n
  1. Have a Dremel<\/a> or equivalent tool?\u00a0 Use the Dremel<\/a> to cut a notch in the screw head.\u00a0 Now take a flat-head screw driver and try and unscrew it using the notch you created.<\/li>\n
  2. If you happen to have a drill<\/a> and some drill bits<\/a> handy, drill a small hole in the center of the screw.\u00a0 No need to drill too deep.\u00a0 The idea here is just to drill a small hole to allow your Phillips (cross head) screw driver to seat deeper in the hole to help it catch better when you turn it.<\/li>\n
  3. If you happen to have an “easy-out” screw extractor<\/a>, this is by far the easiest method.\u00a0 Works pretty much every time and with very little effort.\u00a0 They aren’t that expensive and will save you loads of time messing with stripped screws in the future.<\/li>\n
  4. Use JB Weld<\/a> or equivalently super strong “welding” adhesive to attach a nut to the screw head.\u00a0 Pick a nut that is about the same size as the screw head or at the least such that the diameter of the hole in the middle of the nut is smaller than the diameter of the hole in the screw.\u00a0 Now place the nut centered on top of the screw.\u00a0 Fill the hole with JB weld, being careful to not let it run everywhere.\u00a0 If the nut is flush on the screw, this shouldn’t be a problem.\u00a0 If it can’t be flush, use some sort of quick drying temporary gasket or the like to seal around the edges so that the JB weld doesn’t get everywhere, but rather just stays in the hole.\u00a0 Now let it dry the recommended time.\u00a0 Once it has hardened up, use a socket wrench on the attached nut to remove the screw.<\/li>\n
  5. \"Stripped<\/a>Got a sufficiently wide rubber-band handy?\u00a0 Place it on top of the screw head then try to unscrew the screw slowly pushing really hard.\u00a0 Sometimes the rubber will give you the extra grip needed to get that screw out.<\/li>\n
  6. If you are handy at welding and don’t want to wait for the JB Weld to harden, take a nut and place it on the screw then weld the nut to the screw by welding\u00a0 along the inner part of the nut.\u00a0 Now simply remove as in #5 with a socket wrench.<\/li>\n
  7. If you’ve gotten the screw partially up and the head is exposed, get a pair of needle-nose clamping pliers <\/a>or at the least try a pair of non-clamping needle-nose pliers<\/a>.\u00a0 Many a time my trusty needle-nose clamping pliers have got me out of a “stripped screw” situation.<\/li>\n
  8. A slightly more risky method is to carefully drill the head off the screw.\u00a0 Try not to drill deeply, you just want to take the head off enough to be able to remove whatever piece you are trying to remove.\u00a0 Once the head is off and the piece is removed, enough of the shaft of the screw should be exposed (assuming you didn’t drill it too deep); now use needle-nose pliers to get the shaft of the screw out.<\/li>\n
  9. One of the simplest things to do is if it is a Phillips (cross head) screw, take an appropriately sized flat-head screw driver and, pushing as hard as you can, attempt to remove the screw this way.\u00a0 Often there is plenty of grip available for a flat-head screw driver of the right size in a stripped cross-head screw.\u00a0 If this doesn’t work, combine this method with the rubber band method in step 1.<\/li>\n
  10. Another simple method is to use a Phillips screw driver that is slightly too big for the hole.\u00a0 Push down hard and tilt the Phillips at a slight angle and turn.\u00a0 For a minorly stripped screw, this often works.<\/li>\n
  11. Depending on how fragile the thing you are working on is, you can also try taking a hammer and tapping your screw driver into the screw.\u00a0 If the metal was soft enough to strip in the first place, you will often be able to hammer the screwdriver into the screw head enough to give it a firm position for unscrewing.\u00a0 Obviously this method is no good if what you are working on is fragile.<\/li>\n
  12. If you’ve gotten here and none of the above has worked, it may be time to get out your trusty old over-sized hammer and simply kill the screw…\u00a0 Kill it dead.\u00a0 Collateral damage to the thing you are working on be damned!<\/li>\n<\/ol>\n

    If you liked this article, you might also enjoy our new popular podcast, The BrainFood Show (iTunes<\/a>, Spotify<\/a>, Google Play Music<\/a>, Feed<\/a>), as well as:<\/p>\n